The Project Gutenberg eBook of Jacquard Machines: Instruction Paper
    
This ebook is for the use of anyone anywhere in the United States and
most other parts of the world at no cost and with almost no restrictions
whatsoever. You may copy it, give it away or re-use it under the terms
of the Project Gutenberg License included with this ebook or online
at www.gutenberg.org. If you are not located in the United States,
you will have to check the laws of the country where you are located
before using this eBook.

Title: Jacquard Machines: Instruction Paper

Author: H. William Nelson

Release date: November 22, 2015 [eBook #50532]

Language: English

Credits: Produced by Sharon Joiner, Sam W. and the Online Distributed
        Proofreading Team at http://www.pgdp.net (This file was
        produced from images generously made available by The
        Internet Archive/American Libraries.)


*** START OF THE PROJECT GUTENBERG EBOOK JACQUARD MACHINES: INSTRUCTION PAPER ***




Produced by Sharon Joiner, Sam W. and the Online Distributed
Proofreading Team at http://www.pgdp.net (This file was
produced from images generously made available by The
Internet Archive/American Libraries.)







Transcriber's Note

Italic text is marked with _underscores_, bold text with ~tildes~.




           JACQUARD MACHINES

           INSTRUCTION PAPER


              Prepared by

           H. William Nelson

     Head of Department of Weaving
         Lowell Textile School


   AMERICAN SCHOOL OF CORRESPONDENCE

   CHICAGO                  ILLINOIS

               U. S. A.




           Copyright 1909 by
   American School of Correspondence

  Entered at Stationers' Hall, London
          All Rights Reserved




  [Illustration: CROSS BORDER DOUBLE-LIFT JACQUARD MACHINE
      Thomas Halton's Sons]




JACQUARD MACHINES


The term Jacquard Weaving may be applied to all harness weaving that
is above the range of harness shafts, so that a jacquard machine is
simply a shedding motion whereby a large variety of sheds may be
formed. The greater the number of lifting hooks contained in a
machine, the greater will be the range of patterns that may be woven.
Jacquard machines range from 100 to 2600 hooks.

Since its introduction the jacquard machine has undergone many changes
in regard to the methods of operating the different parts of the
machine, but the principles remain the same.

Jacquard machines may be classed under four heads, as follows:
_First_, Single Action Machines, meaning single cylinder machines;
_second_, Double-Lift Single Cylinder Machines; _third_, Double Action
Machines, meaning double-lift and two cylinders; and _fourth_, Rise
and Fall Machines, which have a close-shed motion. There are also
special machines.

When speaking of a jacquard, all the parts comprising the machine and
the harnesses are included. These may be classified as follows:

(_a_) A number of wire hooks placed vertically in the frame of the
machine.

(_b_) A number of wire needles placed horizontally between the wire
hooks.

(_c_) A number of springs at one end of the needles.

(_d_) Tail cords or neck bands attached to the bottom of the wire
hooks.

(_e_) Harness threads which are attached to a coupling that passes
through the comber board.

(_f_) The coupling, which is usually composed of three or four parts
as follows:

A lingo, usually made of various weights of wire and which is at the
extreme end of the coupling; a double thread, commonly termed a
hanger, which attaches the lingo to a mail eye; and the mail eye,
through which the warp yarn is passed. When there are four parts, a
double thread termed the mid-piece or sleeper is attached to the top
of the eyelet and is then fixed to the harness threads mentioned at
_e_.

(_g_) The cylinder and its working parts.

(_h_) The griffe levers.

(_i_) The griffe.

  [Illustration: Fig. 1. Hooks Resting on Perforated Board.]

  [Illustration: Fig. 2. Flat Hooks.]

~Hooks.~ A description of the great variety of hooks and needles which
have been used and which combine different ideas as to their relative
values and adaption for the various machines in which they were or are
used, will be both interesting and instructive.

In the old jacquard machine the hooks rested on a perforated board,
through which the neck cord passed, and the bottom of the hook was
bent up about five inches, as shown in Fig. 1. Bars were passed
through the turned up portion, as shown in the illustration, to
prevent the hooks from turning. The bars formed a frame which was
lifted when the griffe was raised.

The next hook, as shown in Fig. 2, was flat. This also rested on a
perforated board, and, to assist in keeping the hook in position, the
needle was twisted around the hook. This kind of hook and needle
required too much time and labor when one had to be replaced.

  [Illustration: Fig. 3. Hook Sometimes Used on French Machines.]

  [Illustration: Fig. 4. Common Jacquard Hook.]

The illustration, Fig. 3, shows the next form of hook that was used,
and which is used at the present time in many French machines. This
also rested on a perforated board. The chief object of this hook was
to remove the necessity of having springs to force back the needles.
At the point marked A, a rod passed through the hooks from one side of
the machine to the other, which kept the hooks quite firm. Near the
top of the hook at positions B and B¹, two more rods were placed, one
being at the back of the hook and the other at the front, the bottom
of the hook being held firmly, while the rod B pressing against the
back portion of the hook caused a certain amount of spring.

The rod B¹ was to prevent the hook from swinging under the blades of
the griffe when the latter was descending. The needles used with this
hook had an elbow which pressed against the front of the hook as shown
at C.

  [Illustration: Fig. 5. Showing Deep Griffe Blades.]

What we shall term the ordinary shaped hook, but which formerly was
much thicker, was next used. This is illustrated in Fig. 4. The lower
portion of these hooks passes through a grate, each hook passing
through a single slot. When first used, these hooks were often bent or
"crowned" under the griffe as it descended. In some cases the trouble
was due to the wire from which the hook was made, but more often it
was due to there being too great a distance between the point where
the needle was in contact with the hook, and the griffe, causing the
hook to swing or vibrate. To overcome this defect, deep griffe blades
(shown in Fig. 5) were introduced.

The use of these deep blades made it difficult for the fixer to
replace broken hooks, in addition to adding weight to the machine, so
another change was made, deep and shallow blades being fixed
alternately; using hooks shown in Fig. 6. In this arrangement the long
hooks had a tendency to swing back under the short blade owing to the
great length of the hook, when the loom was run at a high speed.

  [Illustration: Fig. 6. Alternate Arrangement of Griffe Blades.]

The hook illustrated in Fig. 7 was then introduced. It will be noted
the wire extends some distance beyond the point when the wire was bent
to catch on the blade of the griffe. While they were new, these hooks
overcame the difficulty to a certain extent, but as soon as they
became worn, the top portion of the wire would bend and break, falling
into the machine.

  [Illustration: Fig. 7. Showing Hook Extending Above Griffe.]

  [Illustration: Fig. 8. Hooks Used at the Present Time.]

In most of the jacquard machines used at the present time, the griffe
has been lowered to within approximately one inch of the top of the
needles and the hooks have been made of stronger material (shown in
Fig. 8), enabling a more compact machine to be made.




SINGLE ACTION MACHINE


  [Illustration: Fig. 9. Single Action Jacquard Machine.]

The illustration, Fig. 9, shows a jacquard known as the _Single Action
Machine_. The chief feature of this machine is that the same griffe
lifts the hooks for every shed, so the griffe must descend before the
next shed can be lifted. This allows all the yarn to be lifted from
the bottom shed. The single action machine is convenient and well
adapted to work when a high speed is not required; ninety to one
hundred thirty picks per minute being the most suitable speeds.

In the silk industry the single action machine is extensively used as
there is no danger of the cards becoming crossed. This is a very
valuable feature as wrong picks are often placed in the cloth by a
double cylinder machine through the skipping of the cards.

~Construction.~ The single action is the original idea and is the
simplest machine. Fig. 10 shows a sectional view of a 400-hook single
machine. The meaning of the term 400-hook is as follows: There are
four hundred hooks and four hundred needles in the machine which are
in rows of eight hooks and eight needles. It also means that there are
four hundred harness threads to one repeat of the maximum pattern that
can be woven by the machine. Nearly all machines have a few extra
hooks (from 16 to 26) which are often classed with the regular number
of hooks, but are chiefly used for extra work, such as selvedge, extra
harnesses, etc. A pattern of less than four hundred to a repeat can be
woven, by casting out some of the hooks.

Referring to Fig. 10, B is the needle board or plate, through which
the points of the needles E protrude three-eighths or one-half inch. C
is the griffe which is composed of eight blades; H is the spring box,
containing four hundred brass springs which are placed against the
back or loop ends of the needles, one spring for each needle. G is the
grate through which the hooks F pass.

_Needle Plate._ In some cases the needle plate is made of wood and in
others it is made of metal, but the former is undoubtedly the more
economical from every standpoint. Particularly is this shown in the
single cylinder machines where the cylinder travels at a faster rate
of speed than a double cylinder machine, consequently there is more
movement and a larger amount of friction between the needle and needle
board or plate, which results in rapidly wearing out the points of the
needles if a metal plate is used. Worn needle points cause a large
amount of trouble, for in single cylinder machines the cylinder has a
tendency to half-turn when the lay is pushed back by hand, and when
the cylinder returns to the needle points the corner of the cylinder
presses against them and invariably bends a number of the points down
on to the plate. This prevents some of the hooks which ought to be
lifted from being lifted, and causes some hooks to be lifted which
ought to be down.

A composition of powdered black lead and French chalk was used to
prevent the needle points from wearing out, but it was discarded
because the dust was constantly dropping into the harnesses and yarn,
and also was very disagreeable for the weaver.

  [Illustration: Fig. 10. Showing Arrangement of Hooks, Needles,
    Etc.]

A needle board or plate for a 400-machine, has 416 holes, arranged in
52 rows with 8 holes in a row. The rows are divided by a groove into
26 rows on each side. There are also grooves at each end of the needle
board. The grooves are for the lacings which hold the cards together.

The lacing naturally makes the card occupy more space at the ends and
center, because it passes along the upper and under sides of the card,
and if there were no grooves in the needle board, the needles would
have to be made longer so as to allow the points to protrude farther
out from the needle board; or when the card was in contact with the
needle points, the hooks would not be pressed back far enough to
prevent them from being lifted. The grooves are also a great saving on
the lacing of the cards, for if it came in close contact with the
needle board every time the cylinder was drawn in, the lacing would
soon be cut, and this often causes the breakage of cards.

  [Illustration: Fig. 11. Showing Loops for Springs.]

The reason for the extra rows of needles, is to allow the selvedge to
be worked by that row of hooks; also because a jacquard sometimes has
patterns added that require additional harness at the front and back
of the comber board, and the extra needles are used for the working of
the extra harness.

_A spring box_ is seldom used on American machines to hold the springs
that press back the needles, but where the spring box is dispensed
with, a longer loop is made on the back end of the needle (see Fig.
11) and the spring is placed on the loop, with the cotter, which holds
the needles. The spring box, however, is most certainly of value if it
is made to fit squarely in the framework of the machine. The springs
are kept cleaner and consequently will give good results; and if a
spring should break, it can be replaced more readily in a spring box
than if it were on the end of a needle.

There is, however, one disadvantage in using the spring box, for when
the hole, through which the bolt, which holds the box in position,
passes, has become worn, some of the needles will be pressing against
the edge of the spring instead of the center, unless care is taken in
fixing on the box. This causes the needles to stick in the box,
preventing the hooks from working as they ought to do.

  [Illustration: Fig. 12. Hooks Out of Perpendicular with
    Needles.]

_When placing hooks and needles in a machine_, one row of eight
needles is placed in first; that is, the needles are passed through
the bars that extend across the machine from side to side, and into
the holes in the needle board. On the bars the loop of the needle
rests, the bars keeping each 52 needles separate. The first needle is
the one that has the half circle, through which the hook passes,
nearest the needle board at the top (see Fig. 10), and the others are
graded down until the eighth is placed in. This will be the bottom
needle with the half circle nearest the spring box H.

When the cotter has been placed through the loop of the needles, the
hooks are placed in among the needles. The first hook is pressed
through the half circle of the needle and passes on the outside of the
others, which keeps the hook in position. The second is placed through
the half circle of the second needle, but passes on the outside of
the first needle and on the outside of the lower needles. This rule is
followed out until the eighth hook is placed in position.

  [Illustration: Fig. 13. Hooks Out of Perpendicular with
    Needles.]

The grate through which the hooks pass is sometimes made with extra
rows of holes, and is also made so that it can be moved around to help
in the setting of the hooks. For this reason, it is best, after
placing in one row of hooks, to notice if they are straight in the
grate. If they are not straight, and cannot be made straight by moving
the grate, the next row of holes must be used. If the hooks are not
straight, even though they may work freely, the needles, hooks and
grate will be worn out in a very short time.

The hook that passes through the first needle is considered the first
thread in the pattern, although when standing in front of a single
action machine, it is the last thread. In a machine that has the
needle board divided into twenty-six rows at one side of the middle,
and twenty-five at the other side, the twenty-six rows are always at
the left-hand side of the machine, looking at the point of the
needles. (So that the number end of the cards will be at the left hand
side of the machine, looking at the top needle board.)

When all the needles and hooks have been placed in the machine, the
frame, in which the bars that support the top of the needle are fixed,
must be made perfectly straight with the needle board. If they are not
straight with each other, there is endless trouble with the machine.
In the first place, the loop of the needle presses down the spring
when the needle is forced back by the card, instead of pressing the
spring back straight in the box. This will cause the springs to wear
out sooner and they will often stick, preventing the hooks from being
lifted.

In the second place, the needle points will not be straight in the
needle board. This causes the hole in the board to be worn crooked,
also, the dust and oil that get into the back portion of the board has
a greater tendency to bind the needles when they are not straight. The
holes in the needle board at the back are counter sunk, which allows
the needles to be placed in more readily when the machine is being
fixed up, or when a broken needle has to be replaced.

When the hooks and needles have been fixed, the grate, needle board
and needle frame adjusted, the spring box is attached and every needle
is tested and made to work freely. After this is done, the griffe is
placed in the machine. It is absolutely necessary that the griffe be
made to lift straight, and each blade or knife must be in exact
position relative to the hooks, or there will be a number of the hooks
either "crowned" or not lifted when they ought to be. The griffe is
made so that each side can be moved either forward or backward, but it
is sometimes necessary to bend one or two blades of the griffe so as
to have them straight with the hooks. Figs. 12, 13 and 14 show crooked
hooks and needles.

  [Illustration: Fig. 14.]

_When the griffe is set_, the top of the blade ought to be just
touching the hook. If the hook is pressing too hard against the blade,
either the needle point must extend farther out from the needle board,
or the cylinder has to press hard against the needle board when the
hooks have to be pressed off the griffe. Either case is detrimental to
the machine. In the first instance, the cylinder requires to pass
farther out from the needle board, to allow the cards to clear the
needle points when the cylinder is being turned, or there is a
possibility of the edge of the card catching on the needle points,
preventing the cylinder from turning, and causing misspicks. In the
second instance, if the cylinder presses too hard against the needle
board, the lacing is often cut, and the needles have a tendency to
pierce the card where it is blank.

  [Illustration: Fig. 15. Showing Overhead Lever Lift and
    Independent Batten Motion.]

Having set all the inner parts of the machine, the next in order is
the tying on of the neck cords. Carelessness in the setting of the
inner parts so far mentioned cannot afterwards be rectified, and means
the loss of years of work from the machine besides having endless
trouble during the time it is working.

~The Outer Workings of the Machine.~ There are five distinct methods
of operating the movable parts of the machine: _First_, top or
overhead lever lift and independent batten or swing cylinder motion;
_second_, overhead lever and spindle cylinder motion; _third_,
overhead lever and independent slide cylinder motion; _fourth_, bottom
or cradle lever lift, and independent spindle cylinder motion; and
_fifth_, bottom or cradle lever lift and spindle cylinder motion.

The first method is illustrated by Fig. 15. It consists of a lever at
the top of the machine, or in some instances suspended from the beam
that supports the ceiling. The inner end of the lever is connected by
a link to the crossbar of the griffe. This must be fixed exactly in
the center of the crossbar so as to give a straight lift to the
griffe. To the outer end of the lever, a long driving rod is attached.
The bottom end of the driving rod is placed on a stud attached to the
hand wheel, which is fixed on the crank shaft of the boom when the
machine is a single lift. The overhead lever is from thirty-six to
forty inches long, according to the width of the loom. On the
thirty-six inch lever the inner end, which is attached to the crossbar
from the link to the supporting stud, fixed in the bracket attached to
the framework of the machine, is about ten and one-half inches long,
and the longer end, which is attached to the lifting rod, is
twenty-four to twenty-five and two-thirds inches long. The throw from
the center of shaft to the stud fixed to the hand wheel is four
inches. This gives an eight inch stroke on the hand wheel.

    10½ × 8
    -------  = 3⅓ inches
      25

Allowing for the fall of the griffe below the bend of the hook the
movement will give about a three-inch shed in the harnesses.

The batten or swing cylinder movement is shown in detail in Fig. 16.
It is composed of five distinct parts as follows:

(_a_) Two small arms are fixed at the top of the machine, one at each
side. Two pointed set screws with lock nuts are set in the arms and
the batten or swing is supported on these points.

(_b_) The batten, which is in the form of a square iron frame.

  [Illustration: Fig. 16. Details of Batten or Swing Cylinder
    Motion.]

(_c_) Two cups set in the batten frame, which support the cylinder.
The cups are made of iron or brass and are held in place by a bolt
with thumb screw on the outside of the frame of the batten. Set into
the bottom of the batten frame and pressing upwards against the cups,
are two set screws whose purpose is to raise or lower the cylinder.

(_d_) The cylinder. This is a square prism with a number of holes
bored on each side to correspond with the needles in the machine. On
each of the four sides of the cylinder and near each end there is a
small brass peg (shown in Fig. 17) for the purpose of holding the card
in the correct position on the cylinder. (The perforations in the
cards should be over the holes in the cylinder). The pegs are set so
they can be adjusted to the right or left. At the ends of the cylinder
square iron castings with rounded edges are fixed.

(_e_) A spring hammer, the flat end of which rests on the casting on
the end of the cylinder. What might be termed the handle of the hammer
passes through the lower cross rail of the bottom frames and through
the top frame. A spring is placed between the two rails and around the
handle of the hammer. The object of the hammer is to keep the cylinder
perfectly level so that the cylinder will strike the board level.

  [Illustration: Fig. 17. Spring Peg.]

  [Illustration: Fig. 18. Cylinder Out of True with Needle Board.]

Flat springs also are attached to the inside of the batten, the lower
end of the spring pressing the card to the cylinder. It is impossible
to overestimate the value of these springs, especially on single
cylinder machines, for it would be almost impossible to work without
them. Their great value is shown when the cylinder is leaving the
needle board by preventing the card from swinging on to the points of
the needles, and also preventing the cards from slipping off the pegs
as the cylinder is drawn over by the catch.

The catch is fixed to the framework of the machine, and rests on the
square casting fixed to the end of the cylinder. As the cylinder moves
out, the catch comes in contact with the rounded edges of the square
and in this manner the cylinder is turned. There is also another catch
fixed underneath, but it is not in contact with the cylinder, and is
adjusted so that it can be raised up in contact and the top catch
raised from contact with the cylinder. This permits the cylinder to be
turned back when a lost pick has to be found.

  [Illustration: Fig. 19. Iron Bar Supporting Batten Frame.]

At each side of the batten frame toward the lower end, an arm is
fixed. To these arms rods that extend downward are attached, and each
rod is fixed to an arm that is set-screwed on a shaft supported by
brackets fixed to the arch of the loom. At the end of this shaft
another arm is fixed and is connected to the eccentric rod that is
attached to the clamp that encircles the cam or eccentric. The cam is
for the purpose of imparting motion to the batten. The cam generally
used to operate the batten is about three and one-half inches from
center of movement to extreme outside length of cam. The cylinder is
moved out from the needle board from two to three inches.

_For the saving of cards_, a great deal depends upon the movement that
is imparted to the cylinder. The less movement that can be given to
the cylinder, the better; that is, of course, when obtaining the
results required. The cylinder ought to be about one-quarter inch from
the needle points when commencing to turn. Sometimes it is necessary
to have the cylinder a little farther out, especially when the cards
have been stored in a damp place and become warped so that they do not
lie flat on the cylinder. In this case, unless the cylinder is a
little farther out from the needle points when commencing to turn, the
edge of the card will catch on the needle points. This will throw the
cards off the pegs and cause a pick-out. If the distance traveled by
the cylinder is too short, it causes too sharp a turning of the
cylinder, which has a tendency to jump the cards from the pegs; and if
the cylinder moves out too far, there is too much friction on the
working parts, as the larger distance has to be traveled in the same
space of time as the shorter distance.

  [Illustration: Fig. 20. Spindle Cylinder Motion.]

When setting the batten frame by either the set screws or the arms to
which the set screws are attached, the principal point is that the
cylinder must be flat against the needle board, both at the top and
bottom of the board, and have the needle points as near the center of
the holes in the cylinder as possible. It is particularly desirable
that all points be square and straight with the batten motion, because
the batten, moving from a top connection, performs an arc movement,
and if the cylinder does not lie flat against the needle board, some
of the hooks will not be pressed far enough off the griffe, or the
points of the needles will come in contact with the sides or bottom of
the holes in the cylinder and in that case, hooks will be down when
they ought to be lifted. Fig. 18 shows the cylinder set crooked with
the needle board.

The set screw support for the batten frame is a very objectional
feature as will readily be seen, for the frame resting and working on
two points is a great strain and some part of the screw soon becomes
worn. This, of course, lowers the cylinder. When the cylinder is
adjusted by turning the set screw, the frame is not only raised higher
but is moved to the right or left, which throws the cylinder out of
place, thus making double the amount of work to adjust it.

The method of supporting a batten frame on an iron bar is by far the
best, as by this arrangement, the cylinder can be directly adjusted.
The illustration given in Fig. 19, shows this method of supporting the
cylinder.

In the second method of operating the movable parts (see Fig. 20) the
top motion remains the same as in the first, but the method of
operating the cylinder is different. Fixed to each side of the square
iron frame that supports the cylinder, is an iron spindle, which
passes through two brackets which act as slides for the spindle and
are fixed to the frame of the machine. Attached to this cylinder
spindle is a two-inch cranked slotted arm. Attached to the spindle of
the griffe is a small extension on which an iron roller is placed.
This iron roller sets in the slot of the cranked arm; the slot arm
being about seven inches long. The seven inches is divided into three
parts, the top and lower portions being perpendicular, to allow a rest
for the cylinder when it is out from the needle board, and also when
it is in contact with the needle board. As the griffe is lifted, the
roller passing up the slot of the cranked arm forces out the cylinder.
The distance the cylinder is moved cannot be changed to any great
extent, neither can the time of the cylinder be changed, so that when
a warped set of cards is being used, there is always the tendency for
the cards to catch on the needle points.

In the third movement (see Fig. 21), the top motion is the same as the
first and second, but the cylinder movement is distinct. A flat, iron
casting which acts as a slide, is placed on each side of the machine.
These slides are supported by small iron rollers, which are placed in
brackets fixed to the frame of the machine. At the end of the slide, a
brass cup for the cylinder and the spring hammer is fixed. A stud is
attached to the slide. The rod connected to the clamp of the cam (or
what is called the eccentric rod) extends upwards and is attached to
an arm that is set-screwed on a shaft, but extends upwards. This
movement is one of the best. The brackets that support the rollers
are adjustable but seldom in the life of a harness do they require
adjusting, for if the rollers are well oiled they last many years,
because the friction is at the lowest possible point.

  [Illustration: Fig. 21. Showing Overhead Lever Lift and Slide
    Cylinder Motion.]

In the fourth movement a square cradle lever is placed in brackets
near the feet of the machine, and connected to the top of the griffe
spindle by means of an arm attached to the end of the cradle lever.
This is shown in the double-lift machine, Fig. 22. There is an arm at
each side of the machine that is connected to the cradle lever. To the
outer end of the lever the long lifting rod is attached. The length of
the square lever is generally twenty-eight inches from fulcrum to
connection of long lifting rod, and ten inches on the shorter end.
This gives about a four-inch lift to the griffe. The cylinder is
driven by an independent spindle motion. An iron spindle is attached
to the frame that supports the cylinder. The spindle passes through
two slide brackets fixed to the sides of the machine. Between the two
brackets and set-screwed on the spindle is an extension with a stud
attached to the top of it. On this stud, the connecting arm from the
lever is placed. The lever is supported at the top of the same bracket
that supports the square lifting lever. To the outer end of the lever
the eccentric rod is attached, but instead of using a cam to give
motion to the cylinder, one part of a double crank is used, the other
portion is used for lifting the griffe.

The fifth method is the same as the fourth with the exception that the
cylinder is operated by the slotted crank arm same as in the second
method.




DOUBLE-LIFT AND SINGLE CYLINDER MACHINES


The illustration, Fig. 22, shows a machine of this type. The same
methods are used to operate this kind of machine as are used with the
single action with this exception that there must be two lifting
levers, either overhead or cradle levers. The reason for using this
kind of machine is to have an open shed motion, and to gain a little
extra speed; but this naturally drives the cylinder faster,
consequently there is a greater damage done to the cards unless great
care is taken with them and additional appliances used to prevent them
from jumping off the pegs.

The needles and hooks used in this kind of machine are shown in Fig.
23. Each needle has two eyes or curves. The reason for two eyes is as
follows: There is but one cylinder and two griffes, one of which is
descending while the other is ascending. The cylinder has to pass in
for every pick; that is, for each lift of the griffe, which
necessitates the use of double the number of hooks; so that in a
400-machine, there are 800 hooks, without the extra ones. The top bend
of every hook is turned in the same direction, that is, toward the
needle board.

The hook that is used on this machine requires a deep bend at the top
so as to have a firm grip on the griffe blade. This is necessitated by
the method of controlling two hooks with one needle, for it sometimes
happens that one hook is lifted while the other is pressed back by the
cylinder, so that the same thread will not be lifted for the next
pick.

The bottom of the hook is made in the form of a capital letter V. The
reason for this is that it saves a considerable amount of friction by
allowing the bottom of the hook that is lifted to move back a little
as the "partner" hook is being pressed by the needle. This shape of
hook saves the grate through which the bottom of the hook passes. Fig.
23 shows the position occupied by the hooks when one hook is lifted
and the other hook (which passes through the same needle) is pressed
off. The dotted lines show the original positions of the hooks.

  [Illustration: Fig. 22. Double-Lift and Single Cylinder
    Machine.]

  [Illustration: Fig. 23. Needles and Hooks Used in Double-Lift
    and Single Cylinder Machines.]

In addition to the added friction on the needles and hooks, it takes
considerably more time to replace a worn needle than it does in
machines where single needles are used, for a rod has to be
temporarily inserted that will press to one side the two hooks around
which the needle has to go, and it is often necessary to take out the
hooks until the needle has been replaced, particularly if the machine
is an old one, or if deep blades are used in the griffe.




DOUBLE ACTION MACHINE


This means that there are two griffes and two cylinders. The same
methods are used to operate the moving parts, as are used on the
single action machines, but the lever and arms are used in a compound
manner. This machine is undoubtedly the best, where large reproduction
is aimed at, for it can be run 170 or 180 picks per minute. The
illustration, Fig. 24, shows a double action machine.

  [Illustration: Fig. 24. Double Action Jacquard Machine.]

~The shedding motion~ is obtained by means of a double crank fixed on
the end of the pick cam shaft, and to which the long lifting rods are
attached. This is shown in Fig. 25. Cams have been used to take the
place of the double crank, so as to allow a dwell for the shed while
the shuttle is passing through. It is particularly desirable in a
broad loom to have the shed full open for a longer period in order to
give clearance for the shuttle, but the cam motion was proven to be
somewhat detrimental, owing to the quick rise and fall of the
harnesses, which causes the lingoes to jump and to be constantly
breaking off. The neck cords also were constantly breaking. The cam
movement could be used successfully with a jacquard that had not many
harness threads attached to the neck cords, and had heavier lingoes
fixed to the harnesses, but for general use, the double crank is best,
as it gives a more even movement. There is also a short dwell while
passing around the extended part of the crank.

  [Illustration: Fig. 25.]

The time to set the crank is to have it level, that is, the two
extreme points horizontal, when the crank shaft is a little ahead of
the bottom center, or to have the reed about 1½ inches from the cloth
when the shed is level.

  [Illustration: Fig. 26. Showing Connection of Neck Cords to
    Hooks.]

Owing to the general formation of the double action machine, that is,
the use of two hooks for one set of harness threads, there is a
somewhat uneven movement to the harnesses. When a griffe is descending
and some of the hooks that are on the griffe are to be lifted for the
next shed, and the hooks are passing each other at the center of
movement, the angle of the harness threads is changed, for as one hook
is lifted from the top shed, the neck cord attached to the hook that
is at the bottom is slack. When this hook is raised for the next pick,
at the point when all the slack cord is taken up, the uneven movement
is caused, the harnesses swinging over into the line with the lifting
hook. The results from this movement are not so harmful if the
jacquard is tied up proportionally and run at the right speed; but
when the machine is run too fast and the lingoes are too light, also
when the neck cord is too short, a large amount of trouble is caused.
Instead of connecting the harnesses to the hooks, by means of two neck
cords, one is used as shown in Fig. 26. The link answers the purpose
for which it is intended, that is, to take away the slack neck cord.
It also reduced the uneven movement. However, unless the hooks are
kept perfectly straight, the link will not work, and it is common for
a hook to be bent a little underneath the grate.

  [Illustration: Fig. 27. Arrangement of Needles and Hooks in
    Double Action Machine.]

When one neck cord breaks on the ordinary double action machine, the
defect is not readily seen, because the harness cord will be lifted by
the other hook, unless it is a pattern where that particular hook from
which the cord has broken is lifted very often. When the link is used,
all the harness threads that are attached to the link will fall, owing
to the use of only one neck cord; this also occurs on the single
action machine.

~Needles.~ The illustration Fig. 27 shows the arrangement of needles
in a double action machine. The first needle at the top marked A,
controls the hook B, passing down in regular order until the bottom
needle in the right hand needle board, marked C, controls the hook D.
The first needle in the left hand or bottom needle board, marked E,
controls the hook F, which is the partner to D, that is, F and D
control the same harness threads, as will be noticed by the connection
at the bottom G. The eighth needle in the bottom needle board, marked
H, controls the hook K, which is the partner hook to B. The bottom set
of needles is exactly like the top set. They are placed in the same
relative position, but work from the opposite direction.

There being two cylinders on this type of machine, one passes in as
the other is going out. Both cylinders turn toward the machine as
indicated by the arrows, and a glance at the two cards A and B with
holes marked 1 and 2, and needles marked the same will show the two
hooks F and D control the same harness threads.

  [Illustration: Fig. 28. Showing Levers, Supports and Studs.]

It will be noticed that one hook has the top bend bent backward, while
the other bends forward in the same direction as the lower bend of the
hook. The reason for this latter is that it would require more space
in the grate and the needles would have to be longer, which would make
a broader machine if the same shape of hook were used; so that by the
use of these hooks, considerable space is gained.

When cutting cards for a double action machine, each card is cut from
the design singly, just the same as if cutting cards for a single
action machine. After the cards are cut, they are divided, the odd
numbers from the even numbers, so that when laced they form, as it
were, two sets of cards, one set being placed at one side of the
machine and the other set at the other side of the machine.

A double action machine is composed of double the number of working
parts that are on a single action machine, but they are placed so as
to work in different directions, with the exception that with an
independent cylinder motion only one eccentric rod is used, and the
eccentric is placed on the pick cam shaft. But if the cylinders are
operated by a spindle motion, a slotted crank arm is attached to the
lifting rod of each griffe and the cylinder is moved out as the griffe
to which it is attached is raised, one cylinder moving out from
contact with the needle board as the griffe, that comes in contact
with the hook controlled by the needles of that board, is raised, at
the same time the other cylinder is passing in towards the needle
board while the second griffe is descending.

  [Illustration: Fig. 29. Rack Method of Lifting Griffe.]

When using the cradle lever on a double action machine, it is
necessary to have two different sizes of lifting cranks to allow extra
lift for the difference in length of the levers, owing to one of the
levers working on the inside of the other. The length of levers used
is about 30 inches for the longer end, from fulcrum to connection of
lifting rod, and 13 inches for the shortest end on the longer lever.
Fulcrum to connection of lifting arm on the shorter lever is 25
inches, and 10 inches on the shorter end. The double crank is made so
that the one with the 12-inch stroke is attached to the shorter lever,
and the 10-inch stroke operates the longer lever.

  [Illustration: Fig. 30. Pulley and Belt for Lifting Griffe.]

The cradle lever lift is used only on machines that have the harnesses
attached to them by the cross tie system, because by the straight tie
system the machine is turned in the opposite direction; that is, one
set of cards would be over the cloth in the loom, and the other set
over the warp; and in the cross tie system the cards are over the
sides of the loom or over shuttle boxes.

The top lever lift is considered by many to be the best method of
operating the griffes, and this method can be used whether the
harnesses are attached by the straight tie or the cross tie system.
All that is required to be changed is that where as in the straight
tie both the levers are on the same stud, and fixed to one support,
the levers for the cross tie are placed on separate studs with
separate supports. The reason for using separate supports and studs is
to meet the different positions of the griffe bar. (See Fig. 28.)

Other lifting methods have been successfully tried on double action
machines; one being a rack movement shown in Fig. 29 and another a
pulley and belt lift shown in Fig. 30.

The rack movement is as follows: A 1½-inch iron shaft is supported in
bearings fixed to the top of the machine. This shaft extends over the
end of the machine. The supports are bolted to the cross rail of the
griffe, and on these supports the racks are fixed. The shaft passes
between the two racks, and the gear is fixed on the shaft in contact
with the rack. An arm is set-screwed on the outer end of the shaft,
and to this arm a long lifting rod is attached. The bottom of the rod
is placed on a stud attached to the face of a round iron plate that is
set-screwed on the pick cam shaft.

  [Illustration: Fig. 31. Type of Rise and Fall Machine.]

In Fig. 30 the pulley A is supported on a shaft in the same position
as the gear for the rack motion, and to the pulley a strip of belting
B is attached, each end being fixed to the cross rail of the griffe at
C. The belt motion is a simple arrangement, but the griffe must act
freely and perfectly straight or the griffe will not descend low
enough to allow the hooks to be pressed off by the cylinder.




THE RISE AND FALL OR CLOSE SHED MACHINE


The illustration, Fig. 31, shows a machine of this type. Its purpose
is to have all the harnesses level at the center movement. The same
working parts are used on this machine as are used on the single
action, the distinctive difference being that cranked levers are
attached to the usual lifting levers so that the grate through which
the hooks pass can be raised and lowered, and so that the griffe is
raised only half the usual distance.

After the cylinder has pressed off the hooks that are not to be
lifted, the grate descends with these hooks, and at the same time the
griffe raises the hooks that are to be lifted.

On some rise and fall machines, a batten cylinder motion is used, but
is fixed in the opposite position from the usual batten motion; that
is, the batten swings from the bottom instead of from the top of the
machine, the set screws that hold it in position being placed in
brackets fixed near the feet of the machine.

These machines cannot be run at a high speed, 130 being considered
average, but faster speed is obtained when the pattern is equally
balanced so that about the same number of ends are raised, as are
falling. This style of machine is now extensively used for weaving
table cloths, silk goods, etc.




EXAMINATION PAPER


JACQUARD MACHINES

~Read carefully:~ Place your name and full address at the head of the
paper. Any cheap, light paper like the sample previously sent you may
be used. Do not crowd your work, but arrange it neatly and legibly.
_Do not copy the answers from the Instruction Paper; use your own
words, so that we may be sure that you understand the subject._


    1. To what may the term "Jacquard Weaving" be applied?

    2. What are the classifications of Jacquard machines?

    3. What are the chief features of the single action machine?

    4. In what industry is the single action machine most extensively
    used?

    5. What is the use of the extra row of needles in the single
    action machine?

    6. How many methods are there for operating the movable parts of
    a machine, and what are they?

    7. What are the reasons for using "double-lift" and "single
    cylinder" machines?

    8. Why do the needles of double-lift and single cylinder machines
    have two eyes?

    9. Why does the hook on a double-lift and single cylinder machine
    require a deep band at the top?

    10. Why is the bottom of the hook made like the capital letter V?

    11. Describe in detail a double action machine.

    12. Why are two different sizes of lifting cranks necessary in
    using a cradle lever on a double action machine?

    13. What is the "rack" movement?

    14. Describe the rise and fall machine.

    15. Describe fully the working of the Jacquard machine.

    16. How are the cords handled in a Jacquard machine?


~After completing the work, add and sign the following statement:~

    I hereby certify that the above work is entirely my own.

      (Signed)




Transcriber's Note

Minor punctuation errors have been corrected. Hyphenation has been
made consistent.

The following amendment has been made:

    Page 20--extention amended to extension--... is a small
    extention on which an iron roller is placed.







*** END OF THE PROJECT GUTENBERG EBOOK JACQUARD MACHINES: INSTRUCTION PAPER ***


    

Updated editions will replace the previous one—the old editions will
be renamed.

Creating the works from print editions not protected by U.S. copyright
law means that no one owns a United States copyright in these works,
so the Foundation (and you!) can copy and distribute it in the United
States without permission and without paying copyright
royalties. Special rules, set forth in the General Terms of Use part
of this license, apply to copying and distributing Project
Gutenberg™ electronic works to protect the PROJECT GUTENBERG™
concept and trademark. Project Gutenberg is a registered trademark,
and may not be used if you charge for an eBook, except by following
the terms of the trademark license, including paying royalties for use
of the Project Gutenberg trademark. If you do not charge anything for
copies of this eBook, complying with the trademark license is very
easy. You may use this eBook for nearly any purpose such as creation
of derivative works, reports, performances and research. Project
Gutenberg eBooks may be modified and printed and given away—you may
do practically ANYTHING in the United States with eBooks not protected
by U.S. copyright law. Redistribution is subject to the trademark
license, especially commercial redistribution.


START: FULL LICENSE

THE FULL PROJECT GUTENBERG LICENSE

PLEASE READ THIS BEFORE YOU DISTRIBUTE OR USE THIS WORK

To protect the Project Gutenberg™ mission of promoting the free
distribution of electronic works, by using or distributing this work
(or any other work associated in any way with the phrase “Project
Gutenberg”), you agree to comply with all the terms of the Full
Project Gutenberg™ License available with this file or online at
www.gutenberg.org/license.

Section 1. General Terms of Use and Redistributing Project Gutenberg™
electronic works

1.A. By reading or using any part of this Project Gutenberg™
electronic work, you indicate that you have read, understand, agree to
and accept all the terms of this license and intellectual property
(trademark/copyright) agreement. If you do not agree to abide by all
the terms of this agreement, you must cease using and return or
destroy all copies of Project Gutenberg™ electronic works in your
possession. If you paid a fee for obtaining a copy of or access to a
Project Gutenberg™ electronic work and you do not agree to be bound
by the terms of this agreement, you may obtain a refund from the person
or entity to whom you paid the fee as set forth in paragraph 1.E.8.

1.B. “Project Gutenberg” is a registered trademark. It may only be
used on or associated in any way with an electronic work by people who
agree to be bound by the terms of this agreement. There are a few
things that you can do with most Project Gutenberg™ electronic works
even without complying with the full terms of this agreement. See
paragraph 1.C below. There are a lot of things you can do with Project
Gutenberg™ electronic works if you follow the terms of this
agreement and help preserve free future access to Project Gutenberg™
electronic works. See paragraph 1.E below.

1.C. The Project Gutenberg Literary Archive Foundation (“the
Foundation” or PGLAF), owns a compilation copyright in the collection
of Project Gutenberg™ electronic works. Nearly all the individual
works in the collection are in the public domain in the United
States. If an individual work is unprotected by copyright law in the
United States and you are located in the United States, we do not
claim a right to prevent you from copying, distributing, performing,
displaying or creating derivative works based on the work as long as
all references to Project Gutenberg are removed. Of course, we hope
that you will support the Project Gutenberg™ mission of promoting
free access to electronic works by freely sharing Project Gutenberg™
works in compliance with the terms of this agreement for keeping the
Project Gutenberg™ name associated with the work. You can easily
comply with the terms of this agreement by keeping this work in the
same format with its attached full Project Gutenberg™ License when
you share it without charge with others.

1.D. The copyright laws of the place where you are located also govern
what you can do with this work. Copyright laws in most countries are
in a constant state of change. If you are outside the United States,
check the laws of your country in addition to the terms of this
agreement before downloading, copying, displaying, performing,
distributing or creating derivative works based on this work or any
other Project Gutenberg™ work. The Foundation makes no
representations concerning the copyright status of any work in any
country other than the United States.

1.E. Unless you have removed all references to Project Gutenberg:

1.E.1. The following sentence, with active links to, or other
immediate access to, the full Project Gutenberg™ License must appear
prominently whenever any copy of a Project Gutenberg™ work (any work
on which the phrase “Project Gutenberg” appears, or with which the
phrase “Project Gutenberg” is associated) is accessed, displayed,
performed, viewed, copied or distributed:

    This eBook is for the use of anyone anywhere in the United States and most
    other parts of the world at no cost and with almost no restrictions
    whatsoever. You may copy it, give it away or re-use it under the terms
    of the Project Gutenberg License included with this eBook or online
    at www.gutenberg.org. If you
    are not located in the United States, you will have to check the laws
    of the country where you are located before using this eBook.
  
1.E.2. If an individual Project Gutenberg™ electronic work is
derived from texts not protected by U.S. copyright law (does not
contain a notice indicating that it is posted with permission of the
copyright holder), the work can be copied and distributed to anyone in
the United States without paying any fees or charges. If you are
redistributing or providing access to a work with the phrase “Project
Gutenberg” associated with or appearing on the work, you must comply
either with the requirements of paragraphs 1.E.1 through 1.E.7 or
obtain permission for the use of the work and the Project Gutenberg™
trademark as set forth in paragraphs 1.E.8 or 1.E.9.

1.E.3. If an individual Project Gutenberg™ electronic work is posted
with the permission of the copyright holder, your use and distribution
must comply with both paragraphs 1.E.1 through 1.E.7 and any
additional terms imposed by the copyright holder. Additional terms
will be linked to the Project Gutenberg™ License for all works
posted with the permission of the copyright holder found at the
beginning of this work.

1.E.4. Do not unlink or detach or remove the full Project Gutenberg™
License terms from this work, or any files containing a part of this
work or any other work associated with Project Gutenberg™.

1.E.5. Do not copy, display, perform, distribute or redistribute this
electronic work, or any part of this electronic work, without
prominently displaying the sentence set forth in paragraph 1.E.1 with
active links or immediate access to the full terms of the Project
Gutenberg™ License.

1.E.6. You may convert to and distribute this work in any binary,
compressed, marked up, nonproprietary or proprietary form, including
any word processing or hypertext form. However, if you provide access
to or distribute copies of a Project Gutenberg™ work in a format
other than “Plain Vanilla ASCII” or other format used in the official
version posted on the official Project Gutenberg™ website
(www.gutenberg.org), you must, at no additional cost, fee or expense
to the user, provide a copy, a means of exporting a copy, or a means
of obtaining a copy upon request, of the work in its original “Plain
Vanilla ASCII” or other form. Any alternate format must include the
full Project Gutenberg™ License as specified in paragraph 1.E.1.

1.E.7. Do not charge a fee for access to, viewing, displaying,
performing, copying or distributing any Project Gutenberg™ works
unless you comply with paragraph 1.E.8 or 1.E.9.

1.E.8. You may charge a reasonable fee for copies of or providing
access to or distributing Project Gutenberg™ electronic works
provided that:

    • You pay a royalty fee of 20% of the gross profits you derive from
        the use of Project Gutenberg™ works calculated using the method
        you already use to calculate your applicable taxes. The fee is owed
        to the owner of the Project Gutenberg™ trademark, but he has
        agreed to donate royalties under this paragraph to the Project
        Gutenberg Literary Archive Foundation. Royalty payments must be paid
        within 60 days following each date on which you prepare (or are
        legally required to prepare) your periodic tax returns. Royalty
        payments should be clearly marked as such and sent to the Project
        Gutenberg Literary Archive Foundation at the address specified in
        Section 4, “Information about donations to the Project Gutenberg
        Literary Archive Foundation.”
    
    • You provide a full refund of any money paid by a user who notifies
        you in writing (or by e-mail) within 30 days of receipt that s/he
        does not agree to the terms of the full Project Gutenberg™
        License. You must require such a user to return or destroy all
        copies of the works possessed in a physical medium and discontinue
        all use of and all access to other copies of Project Gutenberg™
        works.
    
    • You provide, in accordance with paragraph 1.F.3, a full refund of
        any money paid for a work or a replacement copy, if a defect in the
        electronic work is discovered and reported to you within 90 days of
        receipt of the work.
    
    • You comply with all other terms of this agreement for free
        distribution of Project Gutenberg™ works.
    

1.E.9. If you wish to charge a fee or distribute a Project
Gutenberg™ electronic work or group of works on different terms than
are set forth in this agreement, you must obtain permission in writing
from the Project Gutenberg Literary Archive Foundation, the manager of
the Project Gutenberg™ trademark. Contact the Foundation as set
forth in Section 3 below.

1.F.

1.F.1. Project Gutenberg volunteers and employees expend considerable
effort to identify, do copyright research on, transcribe and proofread
works not protected by U.S. copyright law in creating the Project
Gutenberg™ collection. Despite these efforts, Project Gutenberg™
electronic works, and the medium on which they may be stored, may
contain “Defects,” such as, but not limited to, incomplete, inaccurate
or corrupt data, transcription errors, a copyright or other
intellectual property infringement, a defective or damaged disk or
other medium, a computer virus, or computer codes that damage or
cannot be read by your equipment.

1.F.2. LIMITED WARRANTY, DISCLAIMER OF DAMAGES - Except for the “Right
of Replacement or Refund” described in paragraph 1.F.3, the Project
Gutenberg Literary Archive Foundation, the owner of the Project
Gutenberg™ trademark, and any other party distributing a Project
Gutenberg™ electronic work under this agreement, disclaim all
liability to you for damages, costs and expenses, including legal
fees. YOU AGREE THAT YOU HAVE NO REMEDIES FOR NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY OR BREACH OF CONTRACT EXCEPT THOSE
PROVIDED IN PARAGRAPH 1.F.3. YOU AGREE THAT THE FOUNDATION, THE
TRADEMARK OWNER, AND ANY DISTRIBUTOR UNDER THIS AGREEMENT WILL NOT BE
LIABLE TO YOU FOR ACTUAL, DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE OR
INCIDENTAL DAMAGES EVEN IF YOU GIVE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGE.

1.F.3. LIMITED RIGHT OF REPLACEMENT OR REFUND - If you discover a
defect in this electronic work within 90 days of receiving it, you can
receive a refund of the money (if any) you paid for it by sending a
written explanation to the person you received the work from. If you
received the work on a physical medium, you must return the medium
with your written explanation. The person or entity that provided you
with the defective work may elect to provide a replacement copy in
lieu of a refund. If you received the work electronically, the person
or entity providing it to you may choose to give you a second
opportunity to receive the work electronically in lieu of a refund. If
the second copy is also defective, you may demand a refund in writing
without further opportunities to fix the problem.

1.F.4. Except for the limited right of replacement or refund set forth
in paragraph 1.F.3, this work is provided to you ‘AS-IS’, WITH NO
OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE.

1.F.5. Some states do not allow disclaimers of certain implied
warranties or the exclusion or limitation of certain types of
damages. If any disclaimer or limitation set forth in this agreement
violates the law of the state applicable to this agreement, the
agreement shall be interpreted to make the maximum disclaimer or
limitation permitted by the applicable state law. The invalidity or
unenforceability of any provision of this agreement shall not void the
remaining provisions.

1.F.6. INDEMNITY - You agree to indemnify and hold the Foundation, the
trademark owner, any agent or employee of the Foundation, anyone
providing copies of Project Gutenberg™ electronic works in
accordance with this agreement, and any volunteers associated with the
production, promotion and distribution of Project Gutenberg™
electronic works, harmless from all liability, costs and expenses,
including legal fees, that arise directly or indirectly from any of
the following which you do or cause to occur: (a) distribution of this
or any Project Gutenberg™ work, (b) alteration, modification, or
additions or deletions to any Project Gutenberg™ work, and (c) any
Defect you cause.

Section 2. Information about the Mission of Project Gutenberg™

Project Gutenberg™ is synonymous with the free distribution of
electronic works in formats readable by the widest variety of
computers including obsolete, old, middle-aged and new computers. It
exists because of the efforts of hundreds of volunteers and donations
from people in all walks of life.

Volunteers and financial support to provide volunteers with the
assistance they need are critical to reaching Project Gutenberg™’s
goals and ensuring that the Project Gutenberg™ collection will
remain freely available for generations to come. In 2001, the Project
Gutenberg Literary Archive Foundation was created to provide a secure
and permanent future for Project Gutenberg™ and future
generations. To learn more about the Project Gutenberg Literary
Archive Foundation and how your efforts and donations can help, see
Sections 3 and 4 and the Foundation information page at www.gutenberg.org.

Section 3. Information about the Project Gutenberg Literary Archive Foundation

The Project Gutenberg Literary Archive Foundation is a non-profit
501(c)(3) educational corporation organized under the laws of the
state of Mississippi and granted tax exempt status by the Internal
Revenue Service. The Foundation’s EIN or federal tax identification
number is 64-6221541. Contributions to the Project Gutenberg Literary
Archive Foundation are tax deductible to the full extent permitted by
U.S. federal laws and your state’s laws.

The Foundation’s business office is located at 809 North 1500 West,
Salt Lake City, UT 84116, (801) 596-1887. Email contact links and up
to date contact information can be found at the Foundation’s website
and official page at www.gutenberg.org/contact

Section 4. Information about Donations to the Project Gutenberg
Literary Archive Foundation

Project Gutenberg™ depends upon and cannot survive without widespread
public support and donations to carry out its mission of
increasing the number of public domain and licensed works that can be
freely distributed in machine-readable form accessible by the widest
array of equipment including outdated equipment. Many small donations
($1 to $5,000) are particularly important to maintaining tax exempt
status with the IRS.

The Foundation is committed to complying with the laws regulating
charities and charitable donations in all 50 states of the United
States. Compliance requirements are not uniform and it takes a
considerable effort, much paperwork and many fees to meet and keep up
with these requirements. We do not solicit donations in locations
where we have not received written confirmation of compliance. To SEND
DONATIONS or determine the status of compliance for any particular state
visit www.gutenberg.org/donate.

While we cannot and do not solicit contributions from states where we
have not met the solicitation requirements, we know of no prohibition
against accepting unsolicited donations from donors in such states who
approach us with offers to donate.

International donations are gratefully accepted, but we cannot make
any statements concerning tax treatment of donations received from
outside the United States. U.S. laws alone swamp our small staff.

Please check the Project Gutenberg web pages for current donation
methods and addresses. Donations are accepted in a number of other
ways including checks, online payments and credit card donations. To
donate, please visit: www.gutenberg.org/donate.

Section 5. General Information About Project Gutenberg™ electronic works

Professor Michael S. Hart was the originator of the Project
Gutenberg™ concept of a library of electronic works that could be
freely shared with anyone. For forty years, he produced and
distributed Project Gutenberg™ eBooks with only a loose network of
volunteer support.

Project Gutenberg™ eBooks are often created from several printed
editions, all of which are confirmed as not protected by copyright in
the U.S. unless a copyright notice is included. Thus, we do not
necessarily keep eBooks in compliance with any particular paper
edition.

Most people start at our website which has the main PG search
facility: www.gutenberg.org.

This website includes information about Project Gutenberg™,
including how to make donations to the Project Gutenberg Literary
Archive Foundation, how to help produce our new eBooks, and how to
subscribe to our email newsletter to hear about new eBooks.